Facility Approval for the following processes:

 

  • CLASSIFIED PARTS
  • FLIGHT SAFETY PARTS
  • COMPOSITE BONDING
  • BELL HELICOPTER CERTIFIED CLEAN ROOM
  • ELECTRICAL BONDING

BELL

4006
CADMIUM PLATE – RESTRICTED TO PLATING LOW ALLOY STEELS ONLY
4012
THERMAL FIT ASSEMBLY
4084
BLACK OXIDE – ALLOY STEELS
4138
CHEMICAL CLEANING OF AIRCRAFT MATERIALS
4162
INSTALLATION AND RETENTION OF BEARINGS THROUGH STAKING
4182
CHEMICAL FILM TREATMENT, CLASS 1A
4310
APPLICATION OF SOLID FILM LUBRICANT – RESTRICTED TO SURVEYED OVENS DESIGNATED FMC 1000 S/N 72894 AND BAKE #5 F-1800
4328
BONDED STRUCTURES, CONTOURED, HI TEMP ALSO INCLUDES BPSS 4408,4448,4449, AND 4520.
4328
BONDED STRUCTURES, FLAT , HIGH TEMP BPS 4328
4339
MACHINING OF HONEYCOMB, ALUMINUM
4339
MACHINING OF HONEYCOMB, NON-METALLIC
4352
SECTION I, GENERAL
4352
SECTION II, METHOD V – BRUSH-ON ACID
4352
SECTION V, METHOD II – WET ABRASIVE BLAST
4352
SECTION VI, METHOD III – BRUSH-ON ACID TREATMENT
4352
SECTION VII, METHOD I – DRY ABRASIVE BLASTING
4352
SECTION IX, METHOD I – DRY ABRASIVE BLAST
4352
SECTION II, METHOD III – WET ABRASIVE BLAST – RESTRICTED TO SURFACE PREP AND BOND FOR BUFFER PADS, WEAR PADS, ANTI-FRETTING PADS, SIMILAR ITEMS
4352
SECTION V, METHOD IV – DRY ABRASIVE BLASTING – RESTRICTED TO SURFACE PREP AND BOND FOR BUFFER PADS, WEAR PADS, ANTI-FRETTING PADS, SIMILAR ITEMS
4352
SECTION XII, MISCELLANEOUS
4352
SECTION II, METHOD II- SULFURIC/SODIUM DICHROMATE ETCH
4352
SECTION II, METHOD IV- PHOSPHORIC ACID ANODIZE
4352
SECTION II, METHOD V- BRUSH-ON ACID TREATMENT
4352
SECTION V, METHOD IV- DRY ABRASIVE BLASTING
4352
SECTION VII, METHOD I- DRY ABRASIVE BLASTING
4366
BONDED, REINFORCED FIBERGLASS STRUCTURES BPS 4366
4383
BONDING, LOW DENSITY INSERT MATERIAL WITH HONEYCOMB SANDWICH CONSTRUCTION
4389
CHEMICAL MILLING OF TITANIUM
4402
BONDING MACHINED PARTS BPS 4402
4402
BONDED MACHINE PARTS BPS 4402
4403
BONDING, ADHESIVE, EPOXY-BASED
4403
BONDING, ADHESIVE, EPOXY-BASED
4408
BONDING MACHINED PARTS
4424
TAP HAMMER INSPECTION – APPROVED FOR CLASS II PARTS. SPECIFIC PROCEDURE FOR CLASS I PARTS MUST BE SUBMITTED TO BHTI NDT LAB
4424
TAP HAMMER INSPECTION
4425
BONDING, SPLICING HONEYCOMB CORES & INSTALLING INSERTS
4437
BONDED REINFORCED FIBERGLAS STRUCTURES
4437
BONDED REINFORCED FIBERGLASS STRUCTURES BPS 4437
4446
BONDING, COMPOSITE
4449
BONDED STRUCTURES, FLAT, HI-TEMP BPS 4449 – RESTRICTED TO BUILDING THE 212-030-128 AND ANY DASH NUMBER ASSOCIATED WITH THE DRAWING
4449
BONDED STRUCTURES, FLAT , HIGH TEMP BPS 4449
4453
INSPECTION, CONDUCTIVITY, OF WROUGHT ALUMINUM ALLOY SHEET, BAR, PLATE, FORGINGS & EXTRUSIONS (HT)
4453
INSPECTION, CONDUCTIVITY, OF WROUGHT ALUMINUM ALLOY SHEET, BAR, PLATE FORGINGS & EXTRUSIONS (HT)
4453
INSPECTION, CONDUCTIVITY, OF 2024-T3, T4, T42 BARE AND PRIMED ALUMINUM ALLOY TUBING
4458
STRUCTURAL ADHESIVE BONDING USING INTERMEDIATE -HIGH PERFORM SUPPORT AND UNSUPPORTED ADHESIVE FILM
4458
STRUCTURAL ADHESIVE BONDING USING INTERMEDIATE- HIGH PERFORM SUPPORTED AND UNSUPPORTED ADHESIVE FILM
4465
FLUIDIZED OR ELECTRO-STATIC EPOXY POWDER COATING (BPS 4465,TYPE I)
4467
HARDNESS TESTING
4478
BONDING, FABRICATION OF ROOM TEMP. CURING LAMINATED COMPONENTS
4511
LAMINATE COMPOSITE STRUCTURES
4512
PROCESSING SPECIFICATION FOR 250 F.DEGREE TO 325 F.DEGREE CURE LAMINATE COMPOSITE STRUCTURES
4514
MACHINING, DRILLING & TRIMMING CARBON – VENDOR IS RESTRICTED TO MACHINING OF BUFFER PAD MATERIAL 150-022 AND 150-044
4514
MACHINING, DRILLING & TRIMMING CARBON FIBER COMPOSITES
4528
ELECTRICAL BONDING AND GROUNDING OF A/C STRUCTURES
4528
ELECTRICAL BONDING AND GROUNDING OF A/C STRUCTURES
4542
COLD EXPANDING OF FATIGUE CRITICAL HOLES IN METALS
4548
HIGH INTERFERENCE FIT BUSHING INSTALLATION FOR FATIGUE LIFE IMPROVEMENT
4558
QU INSTALLATION OF NUT PLATES UTILIZING COLD EXPANSION
4570
INSTALLATION OF ADHESIVE BONDED FASTENERS ON COMPOSITE AND METALLIC STRUCTURES
4570
INSTALLATION OF ADHESIVE BONDED FASTENERS ON COMPOSITE AND METALLIC STRUCTURES
4592
IUID: SILK SCREEN
4592
IUID: LABEL / NAMEPLATE – RESTRICTED TO NAMEPLATE/LABELS ENCODED AND SUPPLIED BY CODESOURCE
4592
IUID: DOT PEEN
4594
RETENTION OF BEARINGS UTILIZING RETAINING COMPOUNDS
ADDITION
SUB-CONTRACT TOOLING
ADDITION
INSPECTION DELEGATION
APP-I
SPECIAL REQUIREMENTS FOR OFFLOAD OF BELL PLANNING OPERATIONS
APP-VI
CONTROLLED ITEM PROGRAM SUPPLIER REQUIREMENTS
CORE CAP
TOOLING (LARGE WELDMENTS)
CORE CAP
TOOLING (SMALL WELDMENTS)
CORE CAP
TOOLING (LARGE DIES, DRILL JIGS, FIXTURES)
CORE CAP
TOOLING (SMALL DIES, DRILL JIGS, FIXTURES)
CORE CAP
TOOL, SERVICE
CORE CAP
TOOLING (SMALL 3D INSPECTION)
CORE CAP
TOOLING, LIMITED (RUBBER/SLINGS/ETC.)
CORE CAP
GRIND PER DPS-117
CORE CAP
GROUND SUPPORT EQUIPMENT, SIMPLE
CORE CAP
MACHINING (ASSEMBLIES, LARGE)
CORE CAP
MACHINING (ASSEMBLIES, SMALL)
CORE CAP
MACHINING (DETAILS, LARGE)
CORE CAP
MACHINING (DETAILS, SMALL)
CORE CAP
PROTOTYPE PARTS, RESTRICTED
CORE CAP
TUBE BENDING
CORE CAP
HYDRAULIC ACTUATORS/UNITS
SQRM
METTS MIN. SQRM

LOCKHEED MARTIN

MIL-PRF-24712
POWDER COATING (METRIC) TYPE I
MIL-DTL-5541F
ALUMINUM CHEMICAL FILM TYPE I
SUB-TIER CONTROL
SUPPLIER CONTROL OF SUB-TIER PROCESSES – USE OF LMC APPROVED SUB-TIERS ONLY
ISO 9001:2015
ISO 9001:2015 QMS CERTIFICATION- NO DESIGN
STP 58-211
PHOSPHORIC ACID, ANODIZING OF ALUMINUM
PS 0120
STRUCTURAL ADHESIVE BONDING OF METAL ASSEMBLIES
STP61-213
FABRICATION OF GLASS, FABRIC BASE, EPOXY RESIN, L/P
STP60-103
ADHESIVE BONDING OF HONEYCOMB ASSEMBLIES
PS 2017
FABRICATION OF ADHESIVE BONDED HONEYCOMB SANDWICH
STP51-302
FORMING PER APPENDIX A EFFECTIVE 06-30-2018
MIL-F-18264
PRIME AND PAINT
G700
EPOXY PRIMER/POLYURETHANE TOP COAT
G604
APPLICATION IF FINISH FOR C130 HARDWARE

BOEING

BAC 5514
STRUCTURAL BONDING CLASS HC PER D-16925 (QPL)
BAC 5555
PHOSPHORIC ACID ANODIZE (QPL)
HP4-137
PHOSPHORIC ACID ANODIZING OF ALUMINUM FOR STRUCTURAL ADHESIVE BONDING
HP4-100
ADHESIVE PRIMER CONTROL (QPL)
HP15-96
BONDING-HONEYCOMB NONMETALLIC CORE (QPL)
HP16-30
STRUCTURAL BONDING- HIGH STRENGTH- METALS-NONMETALLIC (QPL)
Boeing Bell Lockheed Martin Northrop Grumman Textron Triump Vertex L3 Rotor Craft Services Kaman Aerosystems